About Us
 Spares & Consumables
 General woodworking
 Glue Mixers
 Grabfast Adhesive
 ACMOS Release Agents
 Contact Us



PVA ref. 701/1  1 kg squeezy bottles, 5 kg and 25 kg containers.
Assembly adhesive for interior components. All round wood adhesive.

PVA ref. TR06  1 kg squeezy bottles, 5 kg and 10 kg containers.
Fast setting interior adhesive. High solids content. Suits solid wood assembly and dowel assembly.

PVA ref. WX/10  1 kg squeezy bottles, 5 kg and 25 kg containers.
Cross linking exterior adhesive for hot, cold or RF curing. Ideal for hand spreading and veneer pressing
PVA ref. WX/10/55  25 kg containers.
Similar to WX/10 but less viscous and suits machine spreading.

Hot Melt.  ref. 3465  25 kg sacks
High resistance to FIRA Gold award.
For straight edge banding and no stringing. For ABS, PVS, wood veneer and solid wood.

Hot Melt.  ref. 300  25 kg sacks
Contour edge banding adhesive. Ideal for shaped work and PVC, due to low temperature application of 160 degrees centigrade.

Urea Formaldehyde   ref. UF 200 25 kg sacks.
A powdered resin complete with hardener, especially for veneer pressing. 2 part powder to 1 part water mix.

PU   ref. PU12   1 litre squeezy bottles & 5.6 kg containers.
For solid wood bonding with tight joints. Gap filling. 10 to 40 minute drying time.
Solvent free.

Nails Free.  ref. ATTAKKO  310 ml cartridge.
High strength bonding for most materials.

Membrane press adhesive.   ref. MPM 25 kg containers.
A one part adhesive for vinyl foils. Cross linking and high heat resistant.

Hot melt sticks.   Ref. 101 5 kg boxes
Transparent and fast setting. Ideal for wood, ceramics, plastics, glass, metal and fabrics. Open time approximately 15 seconds.

Hot melt sticks.   Ref. 106 5 kg boxes
Honey/yellow in colour and particularly good for wood and paper. Ideal for wood, ceramics, glass, metal and paper. Open time approximately 20 seconds.


The VSM480 is a high quality mixer. It is simple to use and paddles are attached quickly and easily.

Featuring a two-speed gearbox and variable speed control this machine is designed to suit all of your mixing needs, and with an ergonomically designed soft-grip handle the user.s comfort is firmly in mind.

Supplied with carry case and mixing paddle, which separates in to two pieces for storage convenience.

Available in either 110v or 240v.

Grabfast contact adhesive

Grabfast is a high-performance, fast-tacking, industrial contact adhesive. Although it was initially designed for bonding decorative laminates to particle board it is now used on a wide variety of substrates including veneers, wood, plastics, fibreglass, rubber, polythene, acrylic, metal, fabric, upholstery and a whole host of other materials.

All you need to get you spraying is a gun, hose, glue canister and roller to give you a permanent high strength bond in minutes.


  • Ease of application - fully adjustable spray pattern to suit the work piece
  • Self contained maintenance free system - ready for instant re-use
  • Fast tack / Long open time - work piece can be handled immediately
  • Low odour - Low solvent content
  • No ozone depleting substances
  • High temperature stability - up to 85c
  • Water resistant
  • Non-flammable adhesive
  • Available in disposable (17kg) or refillable (85kg) canisters.

The initial grab is so good that the substrates that have been bonded can be handled and machined almost immediately. This allows the work piece to be completed without any down time which is crucial in a busy working environment.

The nature of the spray system means that it is maintenance free, clean and cost effective, as compared to normal hand-applied contact adhesive. No more trowelling on of adhesive and waiting for it to go off. Spray both substrates, wait just a few minutes for the adhesive to tack up, and bring them together using a roller to form a permanent bond.


Connect the gun to the canister using the hose and ensure all connections are tight. Finger tight is not secure enough. Hold the gun parallel to the work surface and apply a generous coat. Wait for the adhesive to tack up i.e. to be dry to the touch without any transference to the fingers.

It is important to remember that Grabfast is a contact adhesive and forms its bond by sticking to itself. Hence there must be enough adhesive on both substrates to allow this to happen. Coverage of 80 to 100% is recommended. If it is possible and practical, the ideal procedure is to spray one surface vertically and the other horizontally. On porous surfaces and edge banding a double coat of adhesive is advised. Ensure the first coat has dried before applying the second. Grabfast should not be allowed to puddle or concentrate in any one area.

Grabfast is a pressure-sensitive adhesive so uniform pressure of 50-70lbs should be applied after the two surfaces have been brought together. A hand held pressure roller is ideal for obtaining the strongest bond.

Ideally all substrates to be bonded should be preconditioned prior to use. They should be clean, dry, and grease and dust free. Laminates especially should be stored at approximately 20C with relative humidity of 45-55% for 48 hours before bonding. Air should be allowed to flow freely around the components.

Grabfast dries in 2 minutes under normal conditions. High humidity and low temperature will slow the drying time. If the temperature gets too low bloom can occur. This is where moisture forms on the glue line and blisters may start to appear over time. Never bring the two surfaces together prematurely as solvent will be trapped causing bubbles.

Although the adhesive bonds a wide range of substrates please test in an inconspicuous area first.

All content on this website © Copyright 2004-2010 Realwood Machinery & Consumables Ltd
Unit 29, Edison Road, St Ives, PE27 3LF

Tel: 01480 496660 | Fax: 01480 461366